8414 60 000 8 — Air or vacuum pumps, air or other gas compressors and fans; ventilating or recycling hoods incorporating a fan, whether or not fitted with filters; gas-tight biological safety cabinets, whether or not fitted with filters: hoods having a maximum horizontal side not exceeding 120 cm: other

8414 Air or vacuum pumps, air or gas compressors and fans; ventilating or recycling extractor hoods or cabinets incorporating a fan, whether or not fitted with filters: 8414 10 – vacuum pumps 8414 20 – hand- or foot-operated air pumps 8414 30 – compressors of a kind used in refrigerating equipment 8414 40 – air compressors mounted on a wheeled chassis for towing – fans: 8414 51 – – table, wall, floor, ceiling, roof or window fans, with a self-contained electric motor of a rated output not exceeding 125 W 8414 59 – – other 8414 60 – extractor hoods or cabinets having a maximum horizontal side not exceeding 120 cm 8414 80 – other

This heading covers machinery and apparatus, manual or motor-operated, for compressing air or other gases or for creating a vacuum, and apparatus for circulating air or other gases.

In general, air pumps, vacuum pumps and compressors operate on the same principles and are arranged in much the same way as liquid pumps (piston, rotary, centrifugal or ejector) described in the preceding heading. However, there are special types of pumps to create a high vacuum: diffusion pumps (using oil or mercury), molecular pumps and exciting pumps (getter pumps, cryonaposes). Sometimes diffusion pumps, however, are made from stacks of la. In this case, they are not included in this heading (Chapter 70). Air and vacuum pumps are used: to accelerate boiling, distillation or evaporation under reduced pressure; to create vacuum in electric lamps or tubes, vacuum bulbs, etc. Air pumps are used to pump air and create pressure (such as pumping car tires). Unlike liquid pumps, air or other gas compressors (other than low-pressure compressors or intermittent compressors) are cooled with water or have ribs or other air-cooling devices (surface cooling) to remove heat that the compressor produces. There are several types of compressors, for example, piston reciprocating - translational, centrifugal, axial and rotary. A special type of compressor, a turbocharger driven by exhaust gases, is used in internal combustion piston engines to increase the developed power. Compressors are widely used for compressing gases in cylinders; in chemical processes; in refrigerators, etc. and for compressing air and other gases in tanks for compression air engines, pneumohammers, winches, brakes, pneumatic tubes, ballast tanks submarines, etc. This heading also includes free piston generators for gas turbines consisting of two horizontally moving pistons in the same cylinder. The cylinder at the ends expands, like compression cylinders, on which two other pistons walk, connected to the leading pistons, creating a pneumatic recoil. Leading pistons are diluted through the explosive action of flammable gas and thus move the compression pistons. During the return course of compression pistons, the air in the compression cylinders is compressed and ejected out with the exhaust gases through the exhaust valves. The high pressure of hot gases acts on the rotor of the gas turbine, thus allowing the generator to be used instead of the combustion chamber and gas turbine compressor. The air pumps and compressors of this heading may be equipped with engines or turbines, as may the pumps of heading 8413.Turbines are most commonly used for high pressure compressors and operate on the principle of a multistage gas turbine.

(B) FANS Fans, whether or not fitted with an integral driving motor, are designed to deliver large volumes of air or other gases at comparatively low pressure, or simply to create a movement of the surrounding air. Fans of the first type may operate as exhausters or as blowers (e.g., the industrial blowers used in wind tunnels). They consist of an air screw or a bladed impeller rotating in a casing or ducting, and work on the principle of the rotary or centrifugal compressor. The second type is of simpler construction, consisting of a driven air screw rotating in the open air. Fans are used, inter alia, for the ventilation of mines and of buildings of all kinds, bunkers and ships; for the extraction of dust, steam, smoke, hot gases, etc.; for drying various materials (leather, paper, textile materials, paints, etc.); and in mechanical forced-draught devices for furnaces. This category of goods also includes room fans, whether oscillating or tilting, ceiling, wall, window or desk types, etc. This heading excludes fans with equipment additional to their electric motors and housings (such as large dust-separating cones, filters, cooling or heating elements and heat exchangers), where that equipment gives them the character of more complex machines of other headings, e.g., non-electric air heaters (heading 7322), air conditioning machines (heading 8415), dust collectors (heading 8421), air coolers for the industrial treatment of materials (heading 8419) or for premises (heading 8479), electric space heating apparatus incorporating fans (heading 8516). (C) VENTILATING OR RECYCLING HOODS OR CABINETS INCORPORATING A FAN, WHETHER OR NOT FITTED WITH FILTERS This category of goods includes kitchen hoods incorporating a fan, installed in domestic kitchens or in restaurants, canteens, hospitals, etc., as well as fume cupboards incorporating a fan for laboratories and for industrial purposes. Compressors, air pumps, fans, blowers, etc., specially designed for use with other machines are classified in this heading and not as parts of those machines. PARTS Subject to the general provisions regarding the classification of parts (see the General Explanatory Note to Section XVI), parts of the goods of this heading are also classified here (e.g., pump and compressor casings, vanes, impellers, rotors, blades and pistons). This heading also excludes: (a) exhaust gas turbines (heading 8411); (b) emulsion pumps (heading 8413); (c) pneumatic elevators and conveyors (heading 8428); (d) machines for cleaning, sorting or grading seed, grain or dried leguminous vegetables (heading 8437).

Notes

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. This group does not include:

(a) millstones, grinding stones or other articles of Chapter 68;

(b) equipment or devices (e.g. pumps) of ceramic materials and ceramic parts of machinery or devices of any material (Chapter 69);

(c) laboratory glassware (heading 7017); equipment, devices or other articles for technical purposes or parts thereof of glass (heading 7019 or 7020);

(d) articles of heading 7321 or 7322 or similar articles of other base metals (Chapters 74 to 76 or 78 to 81);

(e) vacuum cleaners of heading 8508;

(f) electromechanical household appliances of heading 8509; digital cameras of heading 8525;

(g) radiators for articles of Section XVII; or

(h) manual mechanical brushes for floor cleaning, without engine (heading 9603).

2. Subject to the provisions of Note 3 to Section XVI and Note 11 to this Chapter, a machine or device which meets the description in one or more of headings 8401 to 8424 or heading 8486 and at the same time the description in one or more headings 8425 to 8480 is included in the relevant heading of the first series of headings or in heading 8486 as the case may be, and not in the second series.

(A) However, heading 8419 does not cover:

(i) seed germination equipment, incubators or brooders (heading 8436);

(ii) machinery for wetting grains (heading 8437);

(iii) diffusion apparatus for the extraction of sugary juice (heading 8438);

(iv) equipment for the heat treatment of textile yarn, textile materials or finished textile articles (heading 8451); or

machining equipment, assemblies or laboratory equipment in which temperature change, even if necessary, is an auxiliary process.

(B) Heading 8422 does not cover:

(i) sewing machines for sewing bags or similar packagings (heading 8452); or

(ii) office equipment of heading 8472.

(C) Heading 8424 does not cover:

(i) paint-blasting printing presses (heading 8443); or

(ii) water jet cutting machines (heading 8456).

3. A machine for processing any material which corresponds to the description of heading 8456 and simultaneously to the description of heading 8457 to 8461, 8464 or 8465 is classified in heading 8456.

4. Heading 8457 covers only metalworking machines other than lathes (including multipurpose lathes) which may perform different types of machining operations by:

(a) the automatic replacement of tools from a tool store or similar device in accordance with the processing program(s);

(b) the automatic application simultaneously or sequentially of different processing heads operating at a fixed workpiece (assembly single-position machines); or

(c) automatic movement of the workpiece to various processing heads (multi-position machines).

5. For the purposes of heading 8462, the term “longitudinal cutting line” for flat products means a process line consisting of a winder, a correct device, a longitudinal cutting device and a winder. The term “cross-cutting line” for flat products means a process line consisting of a unwinder, a correct device and a cutting device.

6. (A) For the purposes of heading 8471, the term “computers” means machines capable of:

(i) store the processing program or programs and at least the information currently necessary to execute the program;

(ii) be freely reprogrammable according to user requirements;

(iii) perform user-defined arithmetic calculations; and

(iv) perform, without human intervention, a processing program requiring the computer to modify its actions by making logical decisions during processing.

(B) Computing machines can be made in the form of systems consisting of a different number of individual blocks.

(C) Subject to the provisions of Notes (D) and (E) below, a block shall be treated as part of a computing system if it satisfies all of the following conditions:

(i) exclusively or principally used in a computing system;

(ii) is capable of being connected to the central processing unit either directly or through one or more other units; and

(iii) is capable of receiving or presenting information in such form (codes or signals) as may be used by the system.

Separately presented computer units are classified in heading 8471.

However, keyboards, X-Y-coordinate input devices and disk storage units which satisfy the conditions laid down in Notes (B) (ii) and (B) (iii) above are in all cases to be regarded as blocks of heading 8471.

(D) Heading 8471 does not cover the following devices, presented separately, even if they meet all the conditions of Note 6(C) above:

(i) printers, copiers, facsimile machines, combined or not;

(ii) apparatus for receiving or transmitting voice, images or other data, including apparatus for providing communications over a wired or wireless communication network (for example, on a local or wide area network);

(iii) loudspeakers and microphones;

(iv) television cameras, digital cameras and video recording cameras;

(v) monitors and projectors not combined with television reception equipment.

(E) Machines containing or working in conjunction with a computer and performing specific functions other than information processing are classified in the headings according to their specific functions or, if this is not possible, in the residual headings.

7. Heading 8482, inter alia, covers polished steel balls whose maximum and minimum diameter does not differ from the nominal diameter by more than 1% or by more than 0.05 mm, whichever is smaller. Other steel balls are classified in heading 7326.

8. A machine which is used for more than one purpose shall be classified as if its primary purpose were the only one.

Subject to the provisions of Note 2 to this Chapter and Note 3 to Section XVI, a machine whose primary purpose is not described in any heading or a machine in which none of its functions is primary is classified in heading 8479, unless the context otherwise provides. Heading 8479 also includes machinery for the manufacture of ropes or ropes (e.g. knitting machines) from metal wire, textile yarn or other materials or from a combination of such materials.

9. For the purposes of heading 8470, the term “pocket” applies only to devices not exceeding 170 x 100 x 45 mm.

10. For the purposes of heading 8485, the term additive manufacturing (also referred to as 3D printing) means the formation of physical objects based on a digital model by successively adding and layering, sealing and curing a material (e.g., metal, plastics or ceramics).

Subject to the provisions of Note 1 to Section XVI and Note 1 to Chapter 84, machines as described in heading 8485 are classified in that heading and no other heading of the Nomenclature.

11. (A) Notes 12(a) and 12(b) to Chapter 85 also apply to the terms “semiconductor devices” and “electronic integrated circuits”, respectively, as used in this note and in heading 8486. However, in this note and in heading 8486, the term "semiconductor devices" also applies to photosensitive semiconductor devices and LEDs.

(B) In this note and in heading 8486, the term “plane display panel production” covers the fabrication of a flat panel of substrates. It does not cover the production of glass or the installation of printed circuit boards or other electronic components on flat panels. The term "flat display panel" does not apply to cathode ray tube technology.

(C) Heading 8486 also includes machinery and apparatus used exclusively or principally for:

(i) producing or eliminating defects in masks and patterns;

assemblies of semiconductor devices or electronic integrated circuits;

(iii) lifting, manipulating, loading or unloading boules, plates, semiconductor devices, electronic integrated circuits and flat display panels.

(D) Subject to the provisions of Note 1 to Section XVI and Note 1 to Chapter 84, machinery meeting the description in heading 8486 is classified in this heading and in no other heading of the Nomenclature.

Subheading notes

English text as published in Annex I to Regulation (EU) 2021/1832 (Combined Nomenclature). The EAEU tariff and the EU nomenclature copy these notes from the same convention. For a Russian declaration the binding version is the Russian one: Annex to Decision No 80 of the EEC Council of 14 September 2021.

1. For the purposes of subheading 8465 20, the term ‘machining centres’ applies only to machine-tools for working wood, cork, bone, hard rubber, hard plastics or similar hard materials, which can carry out different types of machining operations by automatic tool change from a magazine or the like in conformity with a machining programme.

2. For the purposes of subheading 8471 49, the term ‘systems’ means automatic data-processing machines whose units satisfy the conditions laid down in note 6(C) to Chapter 84 and which comprise at least a central processing unit, one input unit (for example, a keyboard or a scanner), and one output unit (for example, a visual display unit or a printer).

3. For the purposes of subheading 8481 20, the expression ‘valves for oleohydraulic or pneumatic transmissions’ means valves which are used specifically in the transmission of ‘fluid power’ in a hydraulic or pneumatic system, where the energy source is supplied in the form of pressurized fluids (liquid or gas). These valves may be of any type (for example, pressure-reducing type, check type). Subheading 8481 20 takes precedence over all other subheadings of heading 8481.

4. Subheading 8482 40 applies only to bearings with cylindrical rollers of a uniform diameter not exceeding 5 mm and having a length which is at least three times the diameter. The ends of the rollers may be rounded.

Additional notes

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. For the purposes of subheadings 8407 10 and 8409 10, the term “aviation engines” shall apply only to engines intended for assembly with an air or rotor.

2. В подсубпозицию 8471 70 300 0 также включаются устройства считывания компакт-дисков, являющиеся запоминающими устройствами вычислительных машин, которые предназначены для считывания сигналов с CD-ROM, аудиокомпакт-дисков и фотокомпакт-дисков и снабжены разъемом для наушников, регулятором громкости или кнопкой пуск/стоп.

Additional notes of the Eurasian Economic Union

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. For the purposes of subheading 8482 10 900 1, the term “gross mass” means the total mass of the goods with all kinds of packaging materials and packagings ensuring their safety during storage and transport. The total weight of the goods does not include the mass of packaging materials or containers that are clearly suitable for reuse.

2. For the purposes of subheading 8415 81 001 0, the term “special production facilities” means premises in which the maintenance of precise values of temperature and humidity is due to the operational requirements of the equipment installed therein, such as machines, computers, switching equipment, surgical equipment, etc., or to the operations performed therein.

3. In subheadings 8427 20 190 1, 8427 90 000 1 and 8436 80 100 1, the date of manufacture shall be determined on the basis of the technical documentation of the manufacturer (technical passport, instruction manual) and the manufacturer's plate, which shall be fixed in a conspicuous, easily accessible place of the machinery and shall not be replaced during operation. If the manufacturer's technical documentation and the manufacturer's plate contain conflicting information about the date of manufacture or there is no information about the manufacturer of the equipment on the date of manufacture, then this technique is considered a technique, since the release of which more than 3 years have passed.

If the manufacturer's information indicates only the year of manufacture, then the date of manufacture of the equipment is considered 1 July of the year of manufacture; if the month and year of manufacture are indicated, the date of manufacture is the 15th day of the month specified in the manufacturer's information.

4. For the purpose of classification of goods in subheading 8482 10 900 1 in the states, whose territories constitute the customs territory of the Eurasian Economic Union, when applying the term "French border of the country of importation", the country of import is understood as the customs territory of the Eurasian Economic Union.

5. For the purpose of subheading 8407 10 000 3, the term “take-off power” means the maximum power developed by an aircraft piston engine.

“Take-off power” is specified in the technical documentation and (or) accompanying documents, measured in kilowatts or horsepower (1 kW corresponds to 1.35962 hp).

6. В подсубпозиции 8421 99 000 5 термин «элементы мембранные рулонного типа для фильтрования или очистки жидкостей» означает устройства цилиндрической формы, состоящие из:

- internal plastic perforated tube on which spirally wound membrane bags;

- drainage material located between membrane bags and glued to them on three sides.

The membrane package consists of a twice folded band of membrane containing an extruded grid inside.

At the ends of the membrane roll-type element, fixing discs and sealing cuffs can be installed.

7. For the purposes of subheading 8415 20 000 2, the term “in a single enclosure” refers to air conditioning units (air conditioners) in which all the elements are combined in a single enclosure, frame or platform.

The term "in a single housing" also applies to air conditioning units (air conditioners) in which the refrigeration compressor, which is part of a given air conditioning unit (air conditioner), is located separately, that is, not combined with the rest of the elements in one housing, on one frame or on one platform.