7214 99 500 0 — Bars and rods of iron or non-alloy steel, only hot-rolled, hot-drawn or hot-extruded, containing by weight < 0.25% of carbon, of square cross-section or of a cross-section other than square or circular (other than of free-cutting steel, smooth bars and rods, for reinforced concrete, or bars and rods containing indentations, ribs, grooves or other deformations produced during the rolling process, or wound after rolling)

7214 Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling: 7214 10 – Forged 7214 20 – Containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling 7214 30 – Other, of free-cutting steel – Other: 7214 91 – – Of rectangular (other than square) cross-section 7214 99 – – Other

Other bars and rods are defined in Note 1 (m) to this Chapter. Bars and rods of this heading are usually obtained by hot-rolling or forging blooms, billets, puddled bars or piles of wrought iron; they are sometimes also obtained by hot-drawing or hot-extrusion. In general, bars and rods can be distinguished from other rolled, forged or drawn products because: (1) they have a more even and better finished surface than puddled bars (heading 7206), blooms, rectangular or round billets, slabs and sheet bars (heading 7207). Their cross-section is uniform and, when square or rectangular, they have sharp edges; (2) they are relatively thicker in relation to their width than the products of heading 7208 or 7211. Bars and rods of this heading are mainly presented in straight lengths or in coils. The products of this heading may be subjected to such surface treatments as: (1) Descaling, pickling, scraping and other processes for removing the scale and crust formed during the heating of the metal. (2) Application of a rough coating intended solely to protect the products from rust or other oxidation, to prevent slipping during

transportation and to facilitate the handling I have, for example, the application of paint coatings containing active anti-corrosion pigment, for example, lead meadow, zinc dust, zinc oxide, zinc chromate, iron oxide (iron meadow, crocus), and unpigmented coatings based on oils, fat, wax, paraffin, graphite, tar or bitum. (3) Removal of small quantities of metal for testing. This heading also covers: (1) Tubs which are rolled with protrusions or recesses (e.g., teeth, grooves, ridges), provided that the shape of their general cross-section corresponds to one of the geometric shapes defined in Note 1(m) to this Chapter; these protrusions or recesses must be designed solely to improve the adhesion to concrete, etc. (2) Tubs which must be specially twisted after rolling, for example, rods rolled with two or more longitudinal rods, which have been obtained from one scrolling rod (3); However, this heading does not include: (a) articles consisting of two or more rolled rods twisted together (heading 7308); (b) cut from rods of a length not exceeding the maximum cross-sectional dimension (heading 7326).

Notes

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. In this chapter, and in the case of Notes 1(d), 1(e) and 1(f), throughout the Nomenclature, the following terms mean:

(a) “dividing cast iron” means an alloy of iron with carbon, unfit for forging, containing more than 2 % by weight of carbon and which may contain one or more other elements within the following limits:

- chromium not more than 10% by weight,

- manganese not more than 6 wt.%,

- phosphorus not more than 3 wt.%,

silicon not more than 8 wt.%,

other elements as a whole not more than 10 wt.%;

(b) “mirror cast iron” means an alloy of iron and carbon containing more than 6 % by weight but not more than 30 % by weight of manganese and, for other components, meeting the conditions specified above in point (a) of this note;

(c) "ferroalloys" means alloys in the form of chunks, dugs, chunks or other primary forms obtained by continuous casting, as well as in the form of granules or powders, agglomerated or non-agglomerated, usually used as additives in the manufacture of other alloys or as deoxidants, desulphurators or other similar purposes in ferrous metallurgy and usually unsuitable for forging, containing 4 wt.% or more iron and one or more of the following elements:

- chromium more than 10% by weight,

- manganese more than 30% by weight,

- phosphorus more than 3 wt.%,

silicon more than 8 wt.%,

other elements in the amount of more than 10 wt.%, excluding carbon, provided the copper content does not exceed 10 wt.%;

(d) "steel" means iron-based alloys other than those referred to in heading 7203 which (except for certain types of castings) are malleable and contain 2 % or less carbon by weight. Chromium steels, however, may contain a higher percentage of carbon.

(e) “corrosion-resistant steel” means alloy steel containing 1.2 % or less carbon by weight and 10.5 % or more chromium by weight, with or without other elements;

(f) "other types of alloy steels" means steels which do not fall within the definition of corrosion-resistant steel and contain one or more of the following elements in the following ratios:

aluminium 0.3 wt.% or more,

boron 0.0008 wt.% or more,

chromium 0.3 wt % or more,

cobalt of 0.3 wt.% or more,

- copper 0.4 wt % or more,

lead of 0.4 wt % or more,

Manganese 1.65 wt.% or more,

molybdenum 0.08 wt.% or more,

nickel 0.3 wt % or more,

niobium 0.06 wt.% or more,

silicon 0.6 wt.% or more,

titanium 0.05 wt.% or more,

tungsten 0.3 wt.% or more,

vanadium 0.1 wt.% or more,

zirconia 0.05 wt.% or more,

other elements (other than sulfur, phosphorus, carbon and nitrogen), taken separately, 0.1 wt.% or more;

(g) “ferrous metal ingots for remelting (shield ingots)” – articles roughly cast in the form of ingots without foundry profit or casts or in the form of shells, having obvious surface defects and differing in chemical composition from the converted cast iron, mirror cast iron or ferroalloys;

(h) “pellets” means articles less than 90 % by weight of which are sieved through a sieve of 1 mm cell size and 90 % by weight of which are sieved through a sieve of 5 mm cell size;

(ij) “Semi-finished products” means articles of continuous cross-section obtained from continuous casting, not subjected to or subjected to primary hot rolling; and other articles of continuous cross-section which have not been treated other than primary hot rolling or rough forging, including blanks for corners, shaped or special profiles.

These products are not supplied in rolls;

(k) “flat rolled” means rolled products of a continuous rectangular (other than square) section which do not fall within the definition of (ij) above and are manufactured as follows:

rolls with consecutively wound layers, or

sheets which, with a thickness of less than 4.75 mm, have a width of at least 10 times the thickness and, with a thickness of 4.75 mm or more, have a width exceeding 150 mm and at least two thicknesses.

Flat-rolled products include articles with a relief surface obtained as a result of rolling (for example, having furrows, protrusions, cages, diamonds) or articles perforated, corrugated or polished, provided that they have not acquired the properties of articles included in other headings.

A flat rolled product of any size other than rectangular or square shall be classified as a product of a width of 600 mm or more, provided that it does not have the characteristics of products of other headings;

(l) “hot rolled rods in free coves” means hot rolled products in freely coiled coves having a continuous cross section in the form of circles, circular segments, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “altered rectangles”, in which the two opposite sides are convex arcs, and the other two sides are straight, equal in length and parallel). These products may have notches, protrusions, grooves or other deformations obtained during rolling (rebars);

(m) “Other bars” means articles which do not fall within any of the above definitions in (ij), (k) or (l) or the definition of wires having the same continuous cross-section along the entire length in the form of circles, circular segments, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “altered rectangles”, in which two opposite sides are convexed arcs, and two equal sides – arcs).

These articles may:

have notches, protrusions, furrows or other deformations obtained during rolling (rebars);

- to be twisted after rolling;

(n) "corners, shaped and special profiles" means articles having the same continuous cross-section along the entire length, which do not fall under any of the definitions in (ij), (k), (l) or (m) or the definition of wire.

This Chapter does not include articles of heading 7301 or 7302.

(o) “wire” means cold-deformed articles in bays having any continuous cross-section of the same length and not falling within the definition of flat-rolled;

(p) "hollow rods for drilling" means hollow rods of any cross-section suitable for drilling, the maximum outer cross-sectional size of which is more than 15 mm, but not more than 52 mm, and the maximum internal size does not exceed 1/2 of the maximum external size. Hollow bars of ferrous metals not complying with this definition are classified in heading 7304.

2. Ferrous metals clad with another ferrous metal are classified as articles of that ferrous metal whose mass prevails.

3. Ferrous metal articles produced by electrolytic deposition, injection molding or sintering shall be classified according to their shape, composition and appearance in the headings of this Chapter for similar hot-rolled articles.

Subheading notes

English text as published in Annex I to Regulation (EU) 2021/1832 (Combined Nomenclature). The EAEU tariff and the EU nomenclature copy these notes from the same convention. For a Russian declaration the binding version is the Russian one: Annex to Decision No 80 of the EEC Council of 14 September 2021.

1. In this chapter, the following expressions have the meanings hereby assigned to them:

(a) Alloy pig iron Pig iron containing, by weight, one or more of the following elements in the specified proportions: — more than 0,2 % of chromium, — more than 0,3 % of copper, — more than 0,3 % of nickel, — more than 0,1 % of any of the following elements: aluminium, molybdenum, titanium, tungsten (wolfram), vanadium.

(b) Non-alloy free-cutting steel Non-alloy steel containing, by weight, one or more of the following elements in the specified proportions: — 0,08 % or more of sulphur, — 0,1 % or more of lead, — more than 0,05 % of selenium, — more than 0,01 % of tellurium, — more than 0,05 % of bismuth.

(c) Silicon-electrical steel Alloy steels containing by weight at least 0,6 % but not more than 6 % of silicon and not more than 0,08 % of carbon. They may also contain by weight not more than 1 % of aluminium but no other element in a proportion that would give the steel the characteristics of another alloy steel.

(d) High-speed steel Alloy steels containing, with or without other elements, at least two of the three elements molybdenum, tungsten and vanadium with a combined content by weight of 7 % or more, 0,6 % or more of carbon and 3 to 6 % of chromium.

(e) Silico-manganese steel Alloy steels containing by weight: — not more than 0,7 % of carbon, — 0,5 % or more but not more than 1,9 % of manganese, and — 0,6 % or more but not more than 2,3 % of silicon, but no other element in a proportion that would give the steel the characteristics of another alloy steel.

2. For the classification of ferro-alloys in the subheadings of heading 7202, the following rule should be observed: A ferro-alloy is considered as binary and classified under the relevant subheading (if it exists) if only one of the alloy elements exceeds the minimum percentage laid down in note 1(c) to this chapter; by analogy, it is considered respectively as ternary or quaternary if two or three alloy elements exceed the minimum percentage. For the application of this rule, the unspecified ‘other elements’ referred to in note 1(c) to this chapter must each exceed 10 % by weight.

Additional note

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. The following terms mean:

- "Electrical steel" (subheadings 7209 16 100 0, 7209 17 100 0, 7209 18 100 0, 7209 26 100 0, 7209 27 100 0, 7209 28 100 0 and 7211 23 200 0) - flat rolled, which at alternating current with a frequency of 50 Hz and a magnetic flux of 1 T has a loss of power per kilogram of mass calculated by the Epstein method:

2.1 W or less if its thickness is less than 0.20 mm,

3.6 W or less if its thickness is not less than 0.20 mm but less than 0.60 mm,

6 W or less if its thickness is not less than 0.60 mm but not more than 1.50 mm;

– “white tin” (subheadings 7210 12 200 0, 7210 70 100 0, 7212 10 100 0 and 7212 40 200 0) – flat rolled (less than 0.5 mm thick) covered with a metal layer containing tin 97 % or more by weight;

– «инструментальная сталь» (подсубпозиции 7224 10 100 0, 7224 90 020 0, 7225 30 100 0, 7225 40 120, 7226 91 200 0, 7228 30 200 0, 7228 40 100 0, 7228 50 200 0 и 7228 60 200 0) – легированные стали, отличные от коррозионностойкой или быстрорежущей стали, содержащие одну из следующих композиций с другими элементами или без них:

less than 0.6 wt % of carbon and 0.7 wt % or more of silicon and 0.05 wt % or more of vanadium or 4 wt % or more of tungsten,

0.8 wt.% or more of carbon and 0.05 wt.% or more of vanadium,

more than 1.2 wt.% of carbon and not less than 11 wt.%, but not more than 15 wt.% of chromium,

0.16 wt.% or more, but not more than 0.5 wt.% of carbon and 3.8 wt.% or more, but not more than 4.3 wt.% of nickel and 1.1 wt.% or more, but not more than 1.5 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum,

0.3 wt.% or more, but not more than 0.5 wt.% of carbon and 1.4 wt.% or more, but not more than 2.1 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum and less than 1.2 wt.% of nickel,

0.3 wt.% or more of carbon and less than 5.2 wt.% of chromium and 0.65 wt.% or more of molybdenum or 0.4 wt.% or more of tungsten,

0.5 wt.% or more but not more than 0.6 wt.% of carbon and 1.25 wt.% or more, but not more than 1.8 wt.% of nickel and 0.5 wt.% or more, but not more than 1.2 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum.