7205 29 000 0 — Granules and powders, of pig iron, spiegeleisen, iron or steel: powders: other

7205 Granules and powders of refining and mirror cast iron, ferrous metals: 7205 10 - granules - powders: 7205 21 - - from alloy steel 7205 29 - - - other

The definition of pellets is given in Note 1(h) to this Chapter. This heading includes granules, that is, fractions of more or less round shapes, and faceted “stars”. The fraction is obtained as a result of pouring liquid ferrous metals into cold water or into a stream of water; stars are obtained by crushing a large fraction or cold crushing of sheets, etc. of hardened metal. These articles are classified in this heading whether or not they have been sorted by size. Shots and asterisks are used to clean and remove scales or surface hardening (shot-blasting) of metal, for polishing or engraving metal or ste kla, for processing stone, etc. They're also

are added to concrete as an aggregate which increases its wear resistance, or to increase its impermeability to X-rays and gamma rays. This heading also covers wire pellets obtained by cutting iron or steel wire, which are used for the purposes described above. (B) POWDERS Powders are defined in Note 8 (b) to Section XV. Powders of pig iron, spiegeleisen, iron or steel are materials suitable for pressing or sintering, obtained by atomising molten iron or steel, by reduction of iron oxides (dry process), by crushing pig iron, sponge iron or steel wire, by precipitation (wet process), by decomposition of iron carbonyl, by electrolysis of aqueous solutions of iron salts or by grinding iron or steel (including ground filings). Various articles can be obtained from these powders (including sponge iron powder) by sintering, among them cores for electromagnetic coils used in telephones, magnetos, etc. They are also used in the manufacture of welding electrodes and powdered welding fluxes, in the chemical industry (especially as reducing agents), and sometimes in the manufacture of pharmaceutical preparations (powder obtained by grinding iron filings). This heading excludes: (a) radioactive iron powders (isotopes) (heading 2844); (b) iron powders put up as medicaments under heading 3003 or 3004; (c) granules and powders of ferro-alloys (heading 7202); (d) filings and turnings of iron or steel (heading 7204); (e) small defective balls for bearings which, although often used for the same purposes as shot, fall in heading 7326 under Note 6 to Chapter 84. Such balls differ from shot in having a more regular and worked surface and in being made of better quality steel.

Sub-Chapter II IRON AND NON-ALLOY STEEL GENERAL Provided that the products are of iron or non-alloy steel, this sub-Chapter covers: (1) Ingots or other primary forms, such as puddled bars, pilings, blocks, lumps, including steel in the molten state (heading 7206). (2) Semi-finished products, such as blooms, billets, rounds, slabs, sheet bars, roughly shaped forgings, blanks for angles, shapes and sections (heading 7207). (3) Flat-rolled products (headings 7208 to 7212). (4) Bars and rods, hot-rolled, in irregularly wound coils (heading 7213) and other bars and rods (heading 7214 or 7215).

(5) Corners, shaped and special profiles (heading 7216). (6) Wire (heading 7217).

Notes

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. In this chapter, and in the case of Notes 1(d), 1(e) and 1(f), throughout the Nomenclature, the following terms mean:

(a) “dividing cast iron” means an alloy of iron with carbon, unfit for forging, containing more than 2 % by weight of carbon and which may contain one or more other elements within the following limits:

- chromium not more than 10% by weight,

- manganese not more than 6 wt.%,

- phosphorus not more than 3 wt.%,

silicon not more than 8 wt.%,

other elements as a whole not more than 10 wt.%;

(b) “mirror cast iron” means an alloy of iron and carbon containing more than 6 % by weight but not more than 30 % by weight of manganese and, for other components, meeting the conditions specified above in point (a) of this note;

(c) "ferroalloys" means alloys in the form of chunks, dugs, chunks or other primary forms obtained by continuous casting, as well as in the form of granules or powders, agglomerated or non-agglomerated, usually used as additives in the manufacture of other alloys or as deoxidants, desulphurators or other similar purposes in ferrous metallurgy and usually unsuitable for forging, containing 4 wt.% or more iron and one or more of the following elements:

- chromium more than 10% by weight,

- manganese more than 30% by weight,

- phosphorus more than 3 wt.%,

silicon more than 8 wt.%,

other elements in the amount of more than 10 wt.%, excluding carbon, provided the copper content does not exceed 10 wt.%;

(d) "steel" means iron-based alloys other than those referred to in heading 7203 which (except for certain types of castings) are malleable and contain 2 % or less carbon by weight. Chromium steels, however, may contain a higher percentage of carbon.

(e) “corrosion-resistant steel” means alloy steel containing 1.2 % or less carbon by weight and 10.5 % or more chromium by weight, with or without other elements;

(f) "other types of alloy steels" means steels which do not fall within the definition of corrosion-resistant steel and contain one or more of the following elements in the following ratios:

aluminium 0.3 wt.% or more,

boron 0.0008 wt.% or more,

chromium 0.3 wt % or more,

cobalt of 0.3 wt.% or more,

- copper 0.4 wt % or more,

lead of 0.4 wt % or more,

Manganese 1.65 wt.% or more,

molybdenum 0.08 wt.% or more,

nickel 0.3 wt % or more,

niobium 0.06 wt.% or more,

silicon 0.6 wt.% or more,

titanium 0.05 wt.% or more,

tungsten 0.3 wt.% or more,

vanadium 0.1 wt.% or more,

zirconia 0.05 wt.% or more,

other elements (other than sulfur, phosphorus, carbon and nitrogen), taken separately, 0.1 wt.% or more;

(g) “ferrous metal ingots for remelting (shield ingots)” – articles roughly cast in the form of ingots without foundry profit or casts or in the form of shells, having obvious surface defects and differing in chemical composition from the converted cast iron, mirror cast iron or ferroalloys;

(h) “pellets” means articles less than 90 % by weight of which are sieved through a sieve of 1 mm cell size and 90 % by weight of which are sieved through a sieve of 5 mm cell size;

(ij) “Semi-finished products” means articles of continuous cross-section obtained from continuous casting, not subjected to or subjected to primary hot rolling; and other articles of continuous cross-section which have not been treated other than primary hot rolling or rough forging, including blanks for corners, shaped or special profiles.

These products are not supplied in rolls;

(k) “flat rolled” means rolled products of a continuous rectangular (other than square) section which do not fall within the definition of (ij) above and are manufactured as follows:

rolls with consecutively wound layers, or

sheets which, with a thickness of less than 4.75 mm, have a width of at least 10 times the thickness and, with a thickness of 4.75 mm or more, have a width exceeding 150 mm and at least two thicknesses.

Flat-rolled products include articles with a relief surface obtained as a result of rolling (for example, having furrows, protrusions, cages, diamonds) or articles perforated, corrugated or polished, provided that they have not acquired the properties of articles included in other headings.

A flat rolled product of any size other than rectangular or square shall be classified as a product of a width of 600 mm or more, provided that it does not have the characteristics of products of other headings;

(l) “hot rolled rods in free coves” means hot rolled products in freely coiled coves having a continuous cross section in the form of circles, circular segments, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “altered rectangles”, in which the two opposite sides are convex arcs, and the other two sides are straight, equal in length and parallel). These products may have notches, protrusions, grooves or other deformations obtained during rolling (rebars);

(m) “Other bars” means articles which do not fall within any of the above definitions in (ij), (k) or (l) or the definition of wires having the same continuous cross-section along the entire length in the form of circles, circular segments, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “altered rectangles”, in which two opposite sides are convexed arcs, and two equal sides – arcs).

These articles may:

have notches, protrusions, furrows or other deformations obtained during rolling (rebars);

- to be twisted after rolling;

(n) "corners, shaped and special profiles" means articles having the same continuous cross-section along the entire length, which do not fall under any of the definitions in (ij), (k), (l) or (m) or the definition of wire.

This Chapter does not include articles of heading 7301 or 7302.

(o) “wire” means cold-deformed articles in bays having any continuous cross-section of the same length and not falling within the definition of flat-rolled;

(p) "hollow rods for drilling" means hollow rods of any cross-section suitable for drilling, the maximum outer cross-sectional size of which is more than 15 mm, but not more than 52 mm, and the maximum internal size does not exceed 1/2 of the maximum external size. Hollow bars of ferrous metals not complying with this definition are classified in heading 7304.

2. Ferrous metals clad with another ferrous metal are classified as articles of that ferrous metal whose mass prevails.

3. Ferrous metal articles produced by electrolytic deposition, injection molding or sintering shall be classified according to their shape, composition and appearance in the headings of this Chapter for similar hot-rolled articles.

Subheading notes

English text as published in Annex I to Regulation (EU) 2021/1832 (Combined Nomenclature). The EAEU tariff and the EU nomenclature copy these notes from the same convention. For a Russian declaration the binding version is the Russian one: Annex to Decision No 80 of the EEC Council of 14 September 2021.

1. In this chapter, the following expressions have the meanings hereby assigned to them:

(a) Alloy pig iron Pig iron containing, by weight, one or more of the following elements in the specified proportions: — more than 0,2 % of chromium, — more than 0,3 % of copper, — more than 0,3 % of nickel, — more than 0,1 % of any of the following elements: aluminium, molybdenum, titanium, tungsten (wolfram), vanadium.

(b) Non-alloy free-cutting steel Non-alloy steel containing, by weight, one or more of the following elements in the specified proportions: — 0,08 % or more of sulphur, — 0,1 % or more of lead, — more than 0,05 % of selenium, — more than 0,01 % of tellurium, — more than 0,05 % of bismuth.

(c) Silicon-electrical steel Alloy steels containing by weight at least 0,6 % but not more than 6 % of silicon and not more than 0,08 % of carbon. They may also contain by weight not more than 1 % of aluminium but no other element in a proportion that would give the steel the characteristics of another alloy steel.

(d) High-speed steel Alloy steels containing, with or without other elements, at least two of the three elements molybdenum, tungsten and vanadium with a combined content by weight of 7 % or more, 0,6 % or more of carbon and 3 to 6 % of chromium.

(e) Silico-manganese steel Alloy steels containing by weight: — not more than 0,7 % of carbon, — 0,5 % or more but not more than 1,9 % of manganese, and — 0,6 % or more but not more than 2,3 % of silicon, but no other element in a proportion that would give the steel the characteristics of another alloy steel.

2. For the classification of ferro-alloys in the subheadings of heading 7202, the following rule should be observed: A ferro-alloy is considered as binary and classified under the relevant subheading (if it exists) if only one of the alloy elements exceeds the minimum percentage laid down in note 1(c) to this chapter; by analogy, it is considered respectively as ternary or quaternary if two or three alloy elements exceed the minimum percentage. For the application of this rule, the unspecified ‘other elements’ referred to in note 1(c) to this chapter must each exceed 10 % by weight.

Additional note

Machine translation. The original is the Russian text of the EAEU tariff, and customs goes by it; this translation is for understanding only and has no legal force.

1. The following terms mean:

- "Electrical steel" (subheadings 7209 16 100 0, 7209 17 100 0, 7209 18 100 0, 7209 26 100 0, 7209 27 100 0, 7209 28 100 0 and 7211 23 200 0) - flat rolled, which at alternating current with a frequency of 50 Hz and a magnetic flux of 1 T has a loss of power per kilogram of mass calculated by the Epstein method:

2.1 W or less if its thickness is less than 0.20 mm,

3.6 W or less if its thickness is not less than 0.20 mm but less than 0.60 mm,

6 W or less if its thickness is not less than 0.60 mm but not more than 1.50 mm;

– “white tin” (subheadings 7210 12 200 0, 7210 70 100 0, 7212 10 100 0 and 7212 40 200 0) – flat rolled (less than 0.5 mm thick) covered with a metal layer containing tin 97 % or more by weight;

– «инструментальная сталь» (подсубпозиции 7224 10 100 0, 7224 90 020 0, 7225 30 100 0, 7225 40 120, 7226 91 200 0, 7228 30 200 0, 7228 40 100 0, 7228 50 200 0 и 7228 60 200 0) – легированные стали, отличные от коррозионностойкой или быстрорежущей стали, содержащие одну из следующих композиций с другими элементами или без них:

less than 0.6 wt % of carbon and 0.7 wt % or more of silicon and 0.05 wt % or more of vanadium or 4 wt % or more of tungsten,

0.8 wt.% or more of carbon and 0.05 wt.% or more of vanadium,

more than 1.2 wt.% of carbon and not less than 11 wt.%, but not more than 15 wt.% of chromium,

0.16 wt.% or more, but not more than 0.5 wt.% of carbon and 3.8 wt.% or more, but not more than 4.3 wt.% of nickel and 1.1 wt.% or more, but not more than 1.5 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum,

0.3 wt.% or more, but not more than 0.5 wt.% of carbon and 1.4 wt.% or more, but not more than 2.1 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum and less than 1.2 wt.% of nickel,

0.3 wt.% or more of carbon and less than 5.2 wt.% of chromium and 0.65 wt.% or more of molybdenum or 0.4 wt.% or more of tungsten,

0.5 wt.% or more but not more than 0.6 wt.% of carbon and 1.25 wt.% or more, but not more than 1.8 wt.% of nickel and 0.5 wt.% or more, but not more than 1.2 wt.% of chromium and 0.15 wt.% or more, but not more than 0.5 wt.% of molybdenum.